Edwards-signaling Genesis Ceiling Horn-Strobe User Manual download pdf

Genesis Ceiling Horn-Strobe Installation Sheet

Description

The Genesis Ceiling Horn-Strobe is a fire alarm notification

appliance designed for indoor ceilings and walls. See Table 1

for a list of model numbers.

Table 1: Models

Description

Number

Horn

-strobe,

15 to 95 multi

-cd, white

ADTGC-HDVM MGC-HDVM

EGC-HDVM XLSGC-HDVM

GC-HDVM ZGC-HDVM

Horn

-strobe,

15 to 95 multi

-cd, white, with

FIRE marking

ADTGCF-HDVM MGCF-HDVM

EGCF-HDVM XLSGCF-HDVM

GCF-HDVM ZGCF-HDVM

Horn

-strobe,

15 to 95 multi

-cd, red, with

FIRE marking

EGCFR-HDVM

GCFR-HDVM

MGCFR-HDVM

Field configurable jumper options are available for selecting

the desired dB output, temporal or steady horn output, and

strobe signal output.

The horn-strobe includes a field configurable switch for

selecting the desired candela output. The candela output

setting is locked in place and remains visible after final

installation.

This strobe features an enhanced synchronization circuit to

comply with the latest requirements of UL 1971 Signaling

Devices for the Hearing Impaired and the latest Canadian

standard CAN/ULC-S526. Synchronized operation requires a

separately installed synchronization control module. See

Table 2 for a list of compatible synchronization modules.

Install this device in accordance with applicable requirements

in the latest editions of the NFPA codes and standards and

Canadian Electrical Code, Part 1, Section 32 and CAN/ULC-

S524, Standard for the Installation of Fire Alarm Systems, and

in accordance with the local authorities having jurisdiction.

Table

2: Compatible synchronization module models

Description

Number

Auto

-sync output module

SIGA-CC1S SIGA-MCC1S

GSA-CC1S GSA-MCC1S

Genesis signal master

remote mount

ADTG1M-RM MG1M-RM

EG1M-RM XLSG1M-RM

G1M-RM ZG1M-RM

Installation

WARNING: To reduce the risk of shock, disconnect all power

and allow 10 minutes for stored energy to dissipate before

handling.

Caution: Electrical supervision requires the wire run to be

broken at each terminal. Do not loop the signaling circuit field

wires around the terminals.

To install the horn-strobe:

1. Remove the cover by depressing the tab on the side of the

unit with a small screwdriver. Turn the cover

counterclockwise to release.

2. Set the horn signal, sound output level, and strobe signal

to the desired settings. See Figure 2.

3. Connect the strobe terminals to the signal circuit field

wiring. You must observe polarity for the unit to function

properly. See Figure 4.

4. Slide the candela switch to the desired candela output (95,

115, 150, or 177 cd) by aligning it with the indicator below

the switch. See Figure 1.

5. Mount the unit onto a compatible electrical box. See

Figure 5.

6. Replace the cover by positioning the alignment arrows

together and rotating the cover clockwise.

7. Test the unit for proper operation.

Figure 1: Candela switch

Candela switch 2. Indicator

1 2 3 4

Summary of Contents

Page 1 - Installation

Page 2

2 / 4 P/N 3100616 • REV 05 • REB 30JAN13 Figure 2: Horn and strobe settings 1. JP1: Horn signal jumper: Cut to change from temporal to steady 2.

Page 3 - Maintenance

P/N 3100616 • REV 05 • REB 30JAN13 3 / 4 Table 4: Sound level output (dBA) Signal VDC High db Low db Temporal 16 79.8 75.0 24 83.3 78.0 3

Page 4 - Contact information

4 / 4 P/N 3100616 • REV 05 • REB 30JAN13 Specifications Voltage Regulated 24 VDC, 24 VFWR Strobe operating current See Table 3 Light output Sele

Comments to this Manuals

No comments

Edwards-signaling Genesis Ceiling Horn-Strobe User Manual

Browse online or download User Manual for Safety Edwards-signaling Genesis Ceiling Horn-Strobe. Edwards Signaling Genesis Ceiling Horn-Strobe User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for Safety Edwards-signaling Genesis Ceiling Horn-Strobe