Edwards-signaling Genesis Speaker Strobe User Manual download pdf

Genesis Speaker-Strobe Installation Sheet

Description

The Genesis Speaker-Strobe is a fire alarm notification

appliance designed for indoor walls. See Table 1 for a list of

model numbers.

Table 1: Models

Description

Number

Speaker

-Strobe,

25 VRMS, 15 to 110

multi

-cd, white

ADTG4-S2VM MG4-S2VM

EG4-S2VM XLSG4-S2VM

G4-S2VM ZG4-S2VM

Speaker

-Strobe,

25 VRMS, 15 to 110

multi

-cd, white, with FIRE

marking

ADTG4F-S2VM MG4F-S2VM

EG4F-S2VM XLSG4F-S2VM

G4F-S2VM ZG4F-S2VM

Speaker

-Strobe,

70 VRMS, 15 to 110

multi

-cd, white

ADTG4-S7VM MG4-S7VM

EG4-S7VM XLSG4-S7VM

G4-S7VM G4-S7VM

Speaker

-Strobe,

70 VRMS, 15 to 110

multi

-cd, white, with FIRE

marking

ADTG4F-S7VM MG4F-S7VM

EG4F-S7VM XLSG4F-S7VM

G4F-S7VM ZG4F-S7VM

Surface mount box, white

ADTG4B MG4B

EG4B XLSG4B

G4B ZG4B

The speaker-strobe includes field configurable switches for

selecting the desired candela output and wattage tap. These

settings lock in place and remain visible after final installation.

This strobe features an enhanced synchronization circuit to

comply with the latest requirements of UL 1971 Signaling

Devices for the Hearing Impaired and the latest Canadian

standard CAN/ULC-S526. Synchronized operation requires a

separately installed synchronization control module. See

Table 2 for a list of compatible synchronization modules.

Install this device in accordance with applicable requirements

in the latest editions of the NFPA codes and standards and

Canadian Electrical Code, Part 1, Section 32 and CAN/ULC-

S524, Standard for the Installation of Fire Alarm Systems, and

in accordance with the local authorities having jurisdiction.

Table 2: Compatible synchronization module models

Description

Number

Auto

-sync output module

SIGA-CC1S SIGA-MCC1S

GSA-CC1S GSA-MCC1S

Genesis signal master

remote mount

ADTG1M-RM MG1M-RM

EG1M-RM XLSG1M-RM

G1M-RM ZG1M-RM

Installation

WARNING: To reduce the risk of shock, disconnect all power

and allow 10 minutes for stored energy to dissipate before

handling.

Caution: Electrical supervision requires the wire run to be

broken at each terminal. Do not loop the signaling circuit field

wires around the terminals.

To install the speaker-strobe:

1. Remove the cover by depressing the tabs on top of the

unit by inserting a small screwdriver from the top and

twisting slightly.

2. If temporal strobe (private mode) operation is desired, cut

jumper JP1. See Figure 2.

3. Connect the speaker and strobe terminals to the signal

circuit field wiring. For the unit to function properly,

observe polarity. See Figure 5.

4. Slide the candela switch to the desired candela output (15,

30, 75, or 95 cd) by aligning it with the indicator below the

switch. See Figure 1.

5. Slide the wattage switch to the desired wattage tap (2 W,

1 W, 1/2 W, or 1/4 W) by aligning it with the indicator

below the switch. See Figure 1.

6. Mount the unit onto a compatible electrical box. See

Figure 4.

7. Replace the cover by aligning it at the bottom and

snapping it in at the top.

8. Test the unit for proper operation.

1 2 3 4

Summary of Contents

Page 1 - Installation

Page 2

2 / 4 P/N 3100273 • REV 07 • REB 30JAN13 Figure 1: Field-configurable switches 1. Candela switch 2. Indicator 3. Wattage switch 4. Bottom Fig

Page 3 - Contact information

P/N 3100273 • REV 07 • REB 30JAN13 3 / 4 Figure 5: Wiring Diagram 1. First speaker-strobe 2. Last speaker strobe 3. EOL resistor, voltage deter

Page 4

4 / 4 P/N 3100273 • REV 07 • REB 30JAN13

Comments to this Manuals

No comments

Edwards-signaling Genesis Speaker Strobe User Manual

Browse online or download User Manual for Safety Edwards-signaling Genesis Speaker Strobe. Edwards Signaling Genesis Speaker Strobe User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for Safety Edwards-signaling Genesis Speaker Strobe