Edwards-signaling 5560MD Series User Manual download pdf

Installation Instructions for Catalog Series 5560MD

Mini-Mi

Signal for Fire Alarm Use

Description and Operation

Edwards Catalog Series 5560M is an integrated communication

system designed to sound 55 system tones or one 20-second voice

message in factory, hallway, office and personnel areas. The Mini-

Mi is available either with or without a strobe. The Mini-Mi has

three modes of operation: stand-alone tone generation, stand-alone

voice generation and system audio operation. The Mini-Mi is in a

NEMA Type 3R enclosure and is UL 1971 and UL 464 Listed.

Five modules are available for use with the Mini-Mi.

INPUT POWER

Catalog Typical Current (A)

Number Voltage* Standby Tone On

5560MD-FJ 24V DC Regulated .03 .130

5560MDR-FJ

5560MDS-FJ 24V DC Regulated .03 .130

5560MDRS-FJ

Installation

Installation should be completed in accordance with either the Na-

tional Electrical Code or the Canadian Electrical Code, applicable

local codes and the latest edition of NFPA72, National Fire Alarm

Code.

1. Remove (4) screws from cover and remove cover. Mount

backplate on a 4" (102 mm) electrical box using (2) #8-32 x 5/8"

screws (provided) and (2) #8 steel washers (provided) or other

suitable hardware. For weatherproof applications, mount to

the Cat. No. 449 back box (purchased separately) using (4) #6-

32 x 3/4" screws (provided) and (4) #8 steel washers (provided)

or other suitable hardware.

3. Insert appropriate module, plugging it into the main board.

Secure to speaker using screws removed in step 2. (See Figure

1.)

4. Connect green ground wire to earth ground.

Feed power source wires from the notification appliance circuit

through the backplate and connect to the unit's power source

leads using wire nuts. Observe polarity for DC units.

For models with strobes, connect a second set of power source

wires to the strobe power leads.

5. Select the appropriate module from below and make

connections and settings as described below.

Audio Coupler Module Boards

Connect incoming 10V, 25V or 70V RMS audio line to AUD (+)

and AUD (-) as shown in Figure 2.

Place the audio voltage jumper on the appropriate audio voltage

(Figure 2).

Tone Module Boards

Set miniature programming switch on the printed circuit board

(Figure 3) for the desired tone. Refer to Table 2.

RS485 Activation

For models with RS485 activation, connect the RS485 wires to

terminals + TX/RX and - TX/RX on the module.

Set the dipswitch on the PC board for the appropriate baud rate

(Table 1) and address (Table 2) as shown in Figures 2 and 3.

Maintenance and Maintenance and

Maintenance and

estest

est

Examine the unit semi-annually for external accumulation of dirt.

Clean if necessary.

The Adaptatone should be tested annually or as required by the

local authority having jurisdiction to ensure continuous service.

Catalog Number Description

556A-M Audio Coupler Module

556A-M485 Audio Coupler Module with RS485 Connectivity

556T-M Tone Module

Electrical Specifications

2. Remove (2) screws holding pc board to speaker in the Mini-Mi

housing and remove pc board. (See Figure 1.)

Cheshire, CT 06410 203-699-3300 (Ph)

203-699-3365 (Cust. Serv. Fax)

203-699-3078 (Tech. Serv. Fax)

CAUTION

During installation, take care not to damage

components on the printed circuit board.

WARNING

Do not apply power to the unit until installation is

completed and housing cover and outlet box cover are

secured.

1 2 3 4

Summary of Contents

Page 1 - 556T-M Tone Module

Installation Instructions for Catalog Series 5560MDMini-MiTM Signal for Fire Alarm UseDescription and OperationEdwards Catalog Series 5560M is an inte

Page 2 - Figure 1. Mini-Mi Housing

P/N 3100815 ISSUE 1APAGE 2Potentiometerto AdjustMain VolumeConnector - PlugAppropriate Module intoMain BoardMounting Holesto SecureModule to SpeakerP

Page 3 - 19200 CLOSED CLOSED

P/N 3100815 ISSUE 1PAGE 3Figure 3. Tone Generator Module556T-MDipswitch for Tone Selection(Refer to Table 2)12345678OPENTable 1. Network Baud Rate s

Page 4 - P/N 3100815 ISSUE 1

Table 2. Tone Programming and Switch ConfigurationDing Dong 0102030405060708090A0B0C0D0E0F101112131415161718191A1B1C1D25262728292A2B2C2D2E2F303132333

Comments to this Manuals

No comments

Edwards-signaling 5560MD Series User Manual

Browse online or download User Manual for Safety Edwards-signaling 5560MD Series. Edwards Signaling 5560MD Series User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for Safety Edwards-signaling 5560MD Series