Edwards-signaling 95 Series User Manual download pdf

Installation Instructions for Catalog Series 90, 92 and 95

AdaptaBeacon

Signals

Description

The catalog series 90, 92 (120 and 240V AC Models only) and 95

AdaptaBeacon signals are UL and cUL listed, general purpose

visual and visual/audible signaling appliances. The 90 and 92

series signals are strobe lights; the 95 signals are strobe lights with

a single pulsing horn.

The 92 series single flash beacons are available in 120VAC, 240V

AC and 250V DC models. The 240V AC and 250V DC versions

have a larger lens assembly than the 120V version. The 92(*)-S1

beacons are supplied with 3 ft (.9 m) flying leads.

The 90, 92 and 95 series are suitable for indoor or outdoor (weath-

erproof) installation and utilize a standard base that allows direct

surface mounting, mounting on a 4" (102 mm) octagon box, or

mounting on 1/2" (13 mm) NPT conduit. When installing in-

doors, the signals may be mounted in any position. For outdoor

installation, the signals must be mounted on conduit with their

lens or dome facing directly up.

Electrical Specifications

90 Series 92-N5 Series 92-R5 and 92-S1

Series

95 Series

Catalog Rated Current

Number Voltage

90(*)-N5 120V 50/60 Hz 0.10 Amp

92(*)-N5 120V 50/60 Hz 0.10 Amp

92(*)-R5 240V 50/60 Hz 0.05 Amp

92(*)-S1 250V DC 0.10 Amp

95(*)-N5 120V 50/60 Hz 0.10 Amp

*The letter (A - amber, B - blue, C - clear, G - green, M -

magenta or R - red) in this position signifies the color the

supplied lens.

Installation

90, 92, and 95 Series

1. Remove the base from the signal using one of the following

applicable procedures.

a. 90 Series: See Figure 1. Remove the screw in the clamp

ring, remove the ring and lift the dome off the signal.

Loosen the three screws in the base of the lens, turn the

lens clockwise and lift it straight up and off of the strobe

tube support plate, being careful not to damage the strobe

tube. Remove the two screws that are partially set into

the raised area of the strobe tube support plate. Then,

grasp the socket (on the strobe tube support plate) and

carefully lift the support plate off of the signal base.

Pull the wires leads out of the conduit entrance hole in

the base. Proceed to step 2.

b. 92 and 95 Series: See Figures 2 and 3. Remove the screw

in the clamp ring and remove the ring.

For the 92-N5 and 95 series, lift the lens/lamp assembly

off of the base and pull the wire leads out of the conduit

entrance hole in the base.

For the 92-R5 and 92-S1 series, lift the lens off of the

signal base, remove the strobe tube support plate and

pull the wire leads out of the conduit entrance hole in the

WARNINGS

To prevent electrical shock, ensure that power is

disconnected before installing the signal.

To prevent leakage and a potential electrical hazard,

use care when disassembling the signal to prevent

tearing of the weatherproof gaskets. If a

component resists removal due to adhesion to a

gasket,

do not

force apart by hand; carefully

separate the components by prying them apart with

a thin blade screwdriver.

Cheshire, CT 06410 203-699-3300 (Ph)

203-699-3365 (Cust. Serv. Fax)

203-699-3078 (Tech. Serv. Fax)

1 2 3 4

Summary of Contents

Page 1 - WARNINGS

Installation Instructions for Catalog Series 90, 92 and 95AdaptaBeacon® SignalsDescriptionThe catalog series 90, 92 (120 and 240V AC Models only) and

Page 2 - P-047550-0898 ISSUE 9

P-047550-0898 ISSUE 9base. Exercise care so as to not tear the gaskets that arepermanently attached to the lens and signal base.Proceed to step 2.2.

Page 3 - CAUTIONS

P-047550-0898 ISSUE 9knock-out holes in the base. Proceed to step 3 for wiringconnections.Mounting on 1/2" (13 mm) NPT ConduitWARNINGTo prevent

Page 4 - 92-N5 Series Signals

P-047550-0898 ISSUE 9Component Used On Catalog or Part NumberXenon Strobe Tube All series except 92-R5 and 92-S1 92-LSTXenon Strobe Tube 92-R5 and 92

Edwards-signaling 95 Series User Manual

Browse online or download User Manual for Safety Edwards-signaling 95 Series. Edwards Signaling 95 Series User Manual

Summary of Contents

Related models: 90 Series

More documents for Safety Edwards Signaling 95 Series

Comments to this Manuals

Edwards-signaling 95 Series User Manual

Browse online or download User Manual for Safety Edwards-signaling 95 Series. Edwards Signaling 95 Series User Manual

Summary of Contents

Related models: 90 Series

More documents for Safety Edwards Signaling 95 Series

Comments to this Manuals

Related products and manuals for Safety Edwards-signaling 95 Series