Edwards-signaling Genesis Low Frequency 520 Hz Horn-Strobe User Manual download pdf

Genesis Low Frequency (520 Hz) Horn-Strobe

Installation Sheet

Description

The Genesis Low Frequency (520 Hz) Horn-Strobe can be

used for applications where a low frequency alarm notification

appliance with strobe light output is required. The device is

designed for wall mounting and indoor use only. See Table 1

for a list of model numbers.

When this device is used as a low frequency sounder in

sleeping quarters, the strobe's candela switch (Figure 1) must

be set to 110 cd.

The horn-strobe includes field-configurable jumper options for

selecting:

• Temporal or steady horn output

• Low dB or high dB output

• Temporal or continuous pattern strobe

The horn-strobe also includes a field-configurable switch for

setting the strobe candela level. This setting is locked in place

and is visible after final installation.

Table 1: Models

Descripti

on Number

Low

frequency (520 Hz) horn, white housing,

no FIRE marking,

standard output clear strobe

light

G4LFWN-HVM

Low

frequency (520 Hz) horn, white housing,

with FIRE marking

, standard output clear

strobe light

G4LFWF-HVM

Low

frequency (520 Hz) horn, red housing, no

FIRE marking,

standard output clear strobe

light

G4LFRN-HVM

Low

frequency (520 Hz) horn, red housing,

with FIRE marking, standard output clear

strobe light

G4LFRF-HVM

Surface wall mount

box, white housing G4B

Surface wall mount

box, red housing G4RB

This strobe features an enhanced synchronization circuit to

comply with the latest requirements of UL 1971. Synchronized

operation requires a separately installed synchronization

device. See the control panel or power supply compatibility list

for compatible synchronization devices.

Installation

Install and wire this device in accordance with applicable

national and local codes, ordinances, and regulations.

The horn-strobe should be mounted so that the entire lens is

not less than 80 in. (2.03 m) and not greater than 96 in.

(2.44 m) above the finished floor. The entire lens should also

be 24 in. (61 cm) or more from the finished ceiling.

WARNING: Electrocution hazard. To avoid personal injury or

death from electrocution, remove all sources of power and

allow stored energy to discharge before installing or removing

equipment.

Note: Electrical supervision requires that you break the wire

run at each terminal. Do not loop wires around the terminals.

1 2 3 4 5 6

Summary of Contents

Page 1 - Installation Sheet

Page 2 - Maintenance

2 / 6 P/N 3102149-EN • REV 02 • ISS 25MAR14 To install the horn-strobe: 1. Remove the cover by using a screwdriver to depress and slightly twist b

Page 3 - Specifications

P/N 3102149-EN • REV 02 • ISS 25MAR14 3 / 6 Figure 3: Surface mount (1) Surface mount box (G4B or G4RB) (2) Horn-strobe (3) Screw (4X provided

Page 4

4 / 6 P/N 3102149-EN • REV 02 • ISS 25MAR14 Table 4: Audible directional characteristics (horizontal pattern) Angle (°) [1] Output (dB) [2] 0 85

Page 5 - Contact information

P/N 3102149-EN • REV 02 • ISS 25MAR14 5 / 6 Figure 7: Typical vertical light output profile, 110 cd setting (1) Intensity (cd) (2) UL minimum r

Page 6

6 / 6 P/N 3102149-EN • REV 02 • ISS 25MAR14

Comments to this Manuals

No comments

Edwards-signaling Genesis Low Frequency 520 Hz Horn-Strobe User Manual

Browse online or download User Manual for Safety Edwards-signaling Genesis Low Frequency 520 Hz Horn-Strobe. Edwards Signaling Genesis Low Frequency 520 Hz Horn-Strobe User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for Safety Edwards-signaling Genesis Low Frequency 520 Hz Horn-Strobe