P/N 3101756 ISSUE 3
© 2010
http://www.edwardssignaling.com Phone: (800) 336-4206 Fax: (800) 454-2363
Description
Edwards 125 Class LED Beacons are UL and cUL listed
signaling appliances rated for NEMA 4X applications. Two
versions of 125 Class Standard LED Beacons are available:
Flashing 65 FPM (125LEDF) and Steady-On (125LEDS).
Both versions can be either surface or conduit mounted.
A protective wire guard, Cat. No. 125GRD, is available.
Electrical Specications
GRAY BASE BLACK BASE
Catalog Number Catalog Number Voltage Current
Flashing LED
125LEDF*24D 125LEDF*24DB 24V DC 0.060A
125LEDF*120A 125LEDF*120AB 120V AC 50/60 Hz 0.097A
Steady-On LED
125LEDS*24D 125LEDS*24DB 24V DC 0.060A
125LEDS*120A 125LEDS*120AB 120V AC 50/60 Hz 0.097A
*Letter in this position indicates lens/LED color:
A - Amber, B - Blue, G - Green, R - Red
Mechanical Specications
Outdoor Locations
Temperature Ratings ........... -31F to +150F (-35C to +66C)
Installation
WARNINGS
To avoid risk of injury, install lens before
energizing the unit.
To avoid the risk of injury, do not remove or
insert lamp when unit is energized.
3. Thread the conduit onto the base of the signal.
4. Turn on power and verify that the signal operates
properly.
Panel Mounting (Figure 2)
WARNING
To prevent electrical shock, ensure that
power is turned off before installing the
signal.
Conduit Mounting (Figure 1)
1. Thread the 18" (457 mm) signal wire leads through either
1/2" or 3/4" conduit into an approved conduit outlet box.
(Product is supplied with a double threaded - 1/2" internal
and 3/4" external - conduit hub.)
2. Wire the beacon as follows:
a. For AC models, use wire nuts (not supplied) and
connect the signal's black and white wire leads to
the power source wires as shown in Figure 1.
b. For DC models, connect the signal's red wire to the
positive power source wire and connect the signal's
black wire to the negative power source wire using
wire nuts (not supplied). Polarity must be observed.
Refer to Figure 1.
Note: When panel mounting the beacon, the surface and
construction details of the panel must be taken into
consideration in order to ensure that the integrity
of the outdoor, NEMA 4X rating is fully maintained.
Installer should evaluate.
1. Place the mounting gasket (supplied) over the hole in
the panel and route the signal wires through the gasket
and the hole in the panel.
2. Insert the base through the hole in the panel and screw
the locking nut (supplied), with the raised locking edge
facing the mounting surface, onto the base to secure the
beacon.
3. Wire the beacon as follows:
a. For AC models, use wire nuts (not supplied) and
connect the signal's black and white wire leads to the
power source wires as shown in Figure 2. Polarity
is not relevant.
b. For DC models, connect the signal's red wire to the
positive power source wire and connect the signal's
black wire to the negative power source wire using
wire nuts (not supplied). Polarity must be observed.
Refer to Figure 2.
4. Turn on power and verify that the signal operates
properly.
Installation Instructions for 125 Class Beacons,
STANDARD LED Models
(2 pages)
(2 pages)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals